Tuesday, November 25, 2008

Reset Printer Canon MP145 and MP160



error ink cartridges are not installed properly (error E5) :

Step 1 : Push Power switch by continue (Tekan Power On/Off)
Step 2 : inserrt plug(Masukan Power, Power Tetap di Tekan)
step 3 : Tekan Tombol Reset 1x, lepaskan Tombol Pwr, Tekan Reset dua kali lagi Sampai Menjadi 0 (tekan tombol tanpa jeda)
Step 4 : Push + display change from 0 to 1 (tekan tombol + untuk merubah 0 ke 1)
Step 5 : Push Power switch again , Printer will be print 1 page(tekan tombol power –> tombol start sampai ngeprint 1 hal.)
step 6 : Open cover (buka tutup printer)
Step 7 : Unplug (cabut kabel power)
Step 8 : Take out ink 40 and 41(lepaskan catridge 40 dan 41)
Step 9 : Insert plug again (pasang kabel power)
Step 10 : Push power switch (tekan tombol power)
Step 11 : Open cover (scan cover) (buka tutup scaner)
Step 12 : Inksert ink 40 , 41 again (masukan catridge 40 dan 41)

waste ink counter (error E16) :

1. Matikan printer (kabel power masih tercolok), tekan dan tahan tombol STOP/RESET kemudian tekan tombol ON/OFF
2. Tahan tombol ON/OFF, tekan tombol STOP/RESET 2x
3. Lepaskan kedua tombol dan printer akan masuk ke SERVICE MODE
4. Printer akan charging
5. Setelah printer selesai charging, tekan tombol STOP/RESET 4x. (Waste ink counter reset)
6. Setiap kali tombol STOP/RESET ditekan, lampu ON/OFF akan berubah warna hijau dan oranye
7. Matikan printer dan cabut kabel POWER
8. Hidupkan kembali printer.

The number of the Reset :
button pressing
LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset
5) Unplug cable power. (for MP145 / MP150)
6) Turn Off Power. (for MP160)

Error Code/Kode Error :
E2-2 = No paper (ASF)
E3-3 = Paper jam
E4 = No ink
E5-5 = The ink cartridges are not installed or a non-supported ink cartridge is installed, or the ink cartridges are not installed properly
E8 = Waste ink absorber full, or platen waste ink absorber full
E9 = The connected digital camera / video camera does not support Camera Direct Printing
E14 = The Ink cartridges whose destination are wrong
E15 = Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 = Failed to scan head alignment sheet
E22 = Carriage error
E23 = Paper feed error
E24 = Purge unit error
E25 = ASF(cam) sensor error
E26 = Internal temperature rise error
E27 = Waste ink absorber full or platen waste ink absorber full
E28 = Ink cartridge temperature rise error -
E29 = EEPROM error
E33 = Paper feed position error
E35 15 = USB Host VBUD overcurrent error - USB
E37 17 = Abnormal motor driver error
E40 20 = Other hardware error
E42 22 = Scanner error

Download manual service printer
Reset Waste_Ink_Canon_Pixma_MP130.pdf
Reset_Waste_Ink_Canon_i320_and_i255.pdf
Reset_Waste_Ink_Canon_Pixma_MPC190.pdf
Reset_Waste_Ink_Canon_Pixma_MP110.pdf
Reset_waste_ink_canon_iP4000.pdf
Reset_Waste_Ink_Printer_Canon_BJC_2000_and_BJC_2100.pdf.html

Download Link :
Reset All type canon MP cklik

2 comments:

  1. This is for an MP145 but it should be the same procedure for other models:

    These are the step How to Reset waste ink counter (error E16) :
    1. Turn off power button (power button is in ),
    Press and Hold STOP/RESET then Push ON/OFF button
    2. Hold ON/OFF button, press STOP/RESET button 2x
    3. Let go of both buttons and printer is in SERVICE MODE
    4. Printer will be readying
    5. After printer is ready, push STOP/RESET button 4x. (Waste ink counter reset)
    6. Every time you push STOP/RESET button ,
    ON/OFF lamp will change green and orange.
    7. cycle power

    ReplyDelete

Service manuals and repair information about laser, dot matrix, label printer and ink jet printers of different makes: HP, Canon, Epson, Ricoh, Star, Xerox, Okidata