Monday, December 22, 2008

Canon Pixma iP1980

CanonPixma iP1980 printers have the same problems and complaints with the Pixma iP1880. So if you have some problems with the printer Pixma iP 1980, try to use the General tool (Resetter) Canon Pixma iP1880 Printer. Trust me, this resetter would work well. Try it and Good Luck.

These are the steps:
1. Turn On iP1980
2. Push and Hold Resume button about 2 minutes
3. Release Resume button
4. Printer back to normal again

To get Permanent , follow the steps here :
Manual Resetter canon Pixma iP1980/1900 Download

Resetter canon Pixma iP1980/1900 Download

Resetter canon Pixma ALL type IP Download


  1. thanks resetter canon ip1980

  2. free download resetter canon ip1980


    Canon Pixma iP1200, iP1300, iP1500, iP1880, iP1980

    Error: The ink’s absorber is full.


    1.) Plug the power cord and the USB cord.
    2.) ON your printer.
    3.) Press and hold the power button. (Do not release until step 7.)
    4.) Remove the power cord.
    5.) After 5 seconds, insert or return the power cord in its socket.
    6.) Press the reset / resume button for two times. (Reset / resume button located below the power button.)
    7.) Release the power button.
    8.) Press the reset/resume button for 4 times.
    9.) Run the IPTools software or the General Tools software for your printer model.

    IPTools Software – can be used only with Canon Pixma iP1200, iP1300, iP1880
    General Tools Software of Canon Pixma iP1880 will be used to reset the Canon Pixma iP1980.

  4. Thanks Anonymous - if only it was that simple.......

  5. CARA RESET Canon iP1980
    CARA RESET Canon iP1980

    Untuk melakukan Ink Full Tank Resetter pada IP 1980 biasanya lampu indikator pada power dan resume berkedip-kedip berulang kali bila itu terjadi lakukan langkah berikutnya :

    1. Hidupkan printer Canon iP1900
    2. Tekan dan tahan tombol Resume selama 2 menit.
    3. Lepaskan tombol Resume.
    4. Printer akan normal kembali.
    5. Apabila masih belum normal juga, lakukan langkah sebagai untuk reset manual dan Reset Sofware

    Langkah Reset Manual

    1. Colokan kabel power Printer dalam keadaan lepas
    2. Tekan dan tahan tombol power dengan jari telunjuk anda kemudian masukan kabel power
    3. Tombol power masih ditahan, kemudian jari tengah andah pencet tombol resume sebanyak dua kali.
    4. Lepas tombol power
    5. Printer sudah tidak berkedip-kedip
    6. Pada tahap ini anda sudah selesai melakukan langkah Reset Manual
    7. Agar permanen silahkan gunakan Reset Sofware.

  6. Berbeda dengan sofware resetter lainnya, sofware IP-Tool cara menggunakannya sangat mudah.

  7. Masuk ke service mode dulu, caranya:
    - matikan printer, cabut kabel power.
    - tekan tombol power, colokan kabel power.
    - tombol power masih ditekan, tekan tombol resume 1 x, lalu lepas (tombol power masih ditekan.
    - tekan tombol resume sekali lagi ( tombol power masih ditekan )
    - lalu lepas tombol power dan tombol resume bersamaan
    Jalankan sofware resetter.
    Good Luck!


  9. Hi Guys.

    This is what the manual says -

    Seven Flashes: FINE Cartridge is not installed in the correct position.
    Confirm that the FINE Cartridges are installed in the appropriate positions.
    See Replacing a FINE Cartridge.

    Now, I haven't ever had this warning, so I don't have any ideas.
    But as so many do seem to be geting it and you are sure you have done everything right, try this from the Canon support pages -

    Issue: Alarm / Power light flashes orange 7 times consecutively (ink cartridge installed incorrectly)
    Solution: Reset the printer

    Resetting the Printer
    By resetting the printer's power, the print buffer is cleared and certain sensors are reset. If there is invalid data in the buffer, or sensors are stuck in a particular mode; errors may occur.
    Follow these steps to reset the printer:

    1. Turn the printer off with the Power button (if available).

    2. Disconnect the data cable from the printer (not applicable to WiFi, Bluetooth or Infrared) .

    3. Unplug the printer's power cord for approximately 10 minutes, and then plug it back in. If troubleshooting a communication issue, reconnect the data cable (not applicable to WiFi, Bluetooth or Infrared).

    4. Turn the printer back on.

    Note: If resetting the printer does not work, please attempt any other solutions that appeared in your search results.If this is a hardware error on the printer, the printer may need to be repaired.

    If that doesn't help, contact them by email and tell them you have a problem. Then post their reply here, so we can all see what they say. I just wonder if there is a problem with their software?

  10. i need canon ip2770 ink levels resetter... pls help..tnx

  11. still i encountered the problem... the cartridge still can not recognized

  12. I bought printer canon pixma ip 1980 was 2 month and I have some problem.
    I want to ask...
    when I print, it was rise a comment from printer :
    "An ink cartridge is not installed properly. Open the printer proper, make sure the ink cartridge is installed properly, and close the cover"
    So what should I do?
    Reset or buy the cartridge...

  13. great info! thanks for sharing it!


    the printer's error is telling that the ink cartridge is empty.. my printer is transformed into continuous ink then it is already full, what is the problem of my printer? help me pls

  15. thanks a lot for a great info you had shared..

  16. canonIP1980 Counter resetter

  17. canon IP 1980 Counter resetter

  18. saya sementara resetter canon ip 1980,,ketika dalam proses saya clik test patern 1 itu langsung muncul warna orange berkedip 5 kali dan hijau 1,,solusinya


Service manuals and repair information about laser, dot matrix, label printer and ink jet printers of different makes: HP, Canon, Epson, Ricoh, Star, Xerox, Okidata