Friday, January 9, 2009

ERROR CODE PIXMA MP150 MP160



E9 The connected digital camera / video camera does not support Camera
Direct Printing
E14 The Ink cartridges whose destination are wrong
E15 Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 Failed to scan head alignment sheet
E22 Carriage error
E23 Paper feed error
E24 Purge unit error
E25 ASF(cam) sensor error
E26 Internal temperature rise error
E27 Waste ink absorber full or platen waste ink absorber full
E28 Ink cartridge temperature rise error -
E29 EEPROM error
E33 Paper feed position error
E35 15 USB Host VBUD overcurrent error - USB
E37 17 Abnormal motor driver error
E40 20 Other hardware error
E42 22 Scanner error

15 comments:

  1. Error code 1;6 ..just a little problem~!!! just identify which catridge that cannot detected...and for MP150,MP160 click button Black or Color with 5 seconds or more...and for mp145 click button start/reset with 5 seconds...

    ReplyDelete
  2. if u using ip1200,1600,1700 or maybe ip1800 click button resume 5seconds

    ReplyDelete
  3. Sir, there's a big diff between "service mode" and "low level" mode. They are not the same.

    Here are instructions:

    The MPTool is designed for service works with the printer Canon MP-Series
    when in Low-Level mode. This is NOT the same as "service mode"

    Currently supported for
    MP150, MP160, MP170, MP180, MP450, MP460. MP150, MP160, MP170, MP180, MP450, MP460.

    BEFORE activating MPTool...you need to

    To activate LOW LEVEL mode:

    1. Unplug the power cord to the printer for a moment.

    2. Then, hold down the on/off button while plugging in the power cord.
    Keep holding the on/off button down.

    3. Right away the green power light (in the button) will turn on solid.
    Keep holding the on/off button down.

    4. Press and release the Stop/Reset button.
    (the button w a red triangle in a red circle)

    5. Now you can release the on/off putton.


    The green power light will go off and the yellow Alarm light will stay on.
    Now you can run MPTOOL and resetting the ink counters will work.

    Your printer will show up as "another" Cannon printer.
    When you finish you must again unplug the power cord for a moment
    and then just plug it back in. After you do this, you'll see both
    printers listed in Printers (controll panel) and one will show as
    offline. You can then rename this offline printer as "Low Mode Canon"
    or whatever works for you so you don't mix it up with other functions.

    These instructions took some time to translate from Russian, so I hope
    you enjoy! Cheers!

    ButtWeasel

    ReplyDelete
  4. Anonymous - I love you!

    ReplyDelete
  5. I did the whole thing, but what is MPTool, I really dont know about printer, I need your help..

    ReplyDelete
  6. Tested the MPTool with mp150 on low-mode. Worked like a charm. Thank you very much.

    ReplyDelete
  7. Canon MPC INKTank FULL

    1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
    the Stop/ Reset button.
    2) When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
    3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a
    service mode. (Waiting for menu selection)
    4) When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to the
    function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in
    orange and green, starting with orange.)note: press 4 times for waste ink counter reset.

    The number of the Reset
    button pressing
    LED Function Remarks
    0 time Green Power off
    1 time Orange Service pattern print
    2 times Green EEPROM print
    3 times Orange EEPROM reset
    4 times Green Waste ink counter reset

    5) Turn off the printer.( it must be turn off)
    then turn it on again. this works. thanks.

    ReplyDelete
  8. Reset manual "Ink Absorber Full" for pixma MP150 ( error message E27).

    Steps by steps how to reset :

    1. Turn off the printer but still connected to a power source
    2. Press stop/reset button, and then press power button to restart
    3. Press power again and then press twice the stop/reset button.
    4. Press power & Stop/reset button together, to enter
    the repair status and power lights will be green,
    5. Press stop/reset button
    1 time Orange Service pattern print
    2 times Green EEPROM print
    3 times Orange EEPROM reset
    4 times Green Waste ink counter reset
    6. Turn off the printer
    7. Unplug the power cable.
    8. Plug the power cable and then turn it on again


    Use this method with your own risk!!

    Error Code :
    E2-2 = No paper (ASF)
    E3-3 = Paper jam
    E4 = No ink
    E5-5 = The ink cartridges are not installed or a non-supported ink cartridge is installed, or the ink cartridges are not installed properly
    E8 = Waste ink absorber full, or platen waste ink absorber full
    E9 = The connected digital camera / video camera does not support Camera Direct Printing
    E14 = The Ink cartridges whose destination are wrong
    E15 = Ink cartridge is not installed E16 - Ink remaining is unknown
    E16-E19 = Failed to scan head alignment sheet
    E22 = Carriage error
    E23 = Paper feed error
    E24 = Purge unit error
    E25 = ASF(cam) sensor error
    E26 = Internal temperature rise error
    E27 = Waste ink absorber full or platen waste ink absorber full
    E28 = Ink cartridge temperature rise error
    E29 = EEPROM error
    E33 = Paper feed position error
    E35 15 = USB Host VBUD overcurrent error - USB
    E37 17 = Abnormal motor driver error
    E40 20 = Other hardware error
    E42 22 = Scanner error

    ReplyDelete
  9. Reset Printer Canon Ip 4300 for error code 6502

    Reset Printer Canon Ip 4300 for error code 6502

    1, With the printer unplug, remove the ink cart to the right ,

    2,Plug in the printer ,Press the POWER button, Do not release the POWER button ,and then press the RESUME button twice in succession .Now release the POWER button ,press the RESUME button 4 times .

    3,The beeper may sound once ,Then With the printer unplug ,after that reset the printer electronics ,open the printer and this process is finished.

    ReplyDelete
  10. Canon MP750 Error Codes – MultiFunction Printer

    Canon MP750 Error Codes – MultiFunction Printer
    Jul.07, 2008 in Canon, Canon Printer, Error Message

    canon_mp750.jpg

    #001 TX Document has jammed
    #003 TX/RX Document is too long, or page time-over
    #005 TX/RX Initial identification (T0/T1) time-over
    #009 RX Recording paper has jammed or the recordingpaper has run out
    #011 RX Polling reception error
    #012 TX The other party has run out of recording paper
    #018 TX/RX Auto dialing transmission error
    #021 RX The other party has rejected the machineduring polling reception
    #022 TX Call fails#037 RX Memory has overflowed when receivingimages
    #085 TX Other party does not support ITU-T ColorFaxing
    #995 TX/RX Memory Communication reservationcancellation

    ReplyDelete
  11. Reset manual ‘Ink Absorber Full’ untuk pixma MP145 ‘Tested’

    Reset manual “Ink Absorber Full” untuk pixma MP145 (Pesan error E27) sebenarnya , cara kerjanya sedikit mirip dengan MP 150 atau MP 160, begini caranya :

    - Entering service Mode

    1. Matikan printer (pake tombol power, tdk dicabut powernya)
    2. Tekan tombol stop / reset (jangan dilepas)
    3. Tekan tombol power (sampai led power menyala)
    4. Tekan tombol stop/reset, tekan lagi tombol stop/reset 2 kali (jadi semuanya 3 kali)
    5. Tunggu sampai LED seven segment (bukan led power) menunjuk angka 0 >>> BAGIAN YANG PENTING
    6. Tekan tombol stop/reset 4 kali
    7. Tekan Tombol power 1 kali (Roller kertas akan berputar, led power berkedip)
    8. Tunggu sampai LED berhenti berkedip dan printer stand by
    9. Tekan tombol power untuk mematikan printernya dan
    10 Nyalakan lagi…

    ReplyDelete
  12. CANON WASTE TANK RESET CODES]

    hello to you guys! thank you very much the code that you have provided for my canon pixma mp150 was really a great help. I save a lot of time and money i don't have to sent my printer back to canon for their "service". its only a matter of people like you with good will to help others out there from all parts of the world. Its really great. to make it simple for others out there this is the instructions i followed:

    1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
    the Stop/ Reset button.
    2) When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
    3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a
    service mode. (Waiting for menu selection)
    4) When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to the
    function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in
    orange and green, starting with orange.)note: press 4 times for waste ink counter reset.

    The number of the Reset
    button pressing
    LED Function Remarks
    0 time Green Power off
    1 time Orange Service pattern print
    2 times Green EEPROM print
    3 times Orange EEPROM reset
    4 times Green Waste ink counter reset

    5) Turn off the printer.( it must be turn off)
    then turn it on again. this works. thanks.

    ReplyDelete
  13. Hi,

    I got error #7 appear when i switch on my MP145 printer.

    Does anybody here know how to resolve that problem?

    Thanks.

    ReplyDelete
  14. i dismantle my MP 160 and want to use the scanner only as ive thrown the bottom part of it.. ive made all the connections but it shows the error: code:2,250,0

    ReplyDelete
  15. Does anyone know how to alleviate the problem with a Canon pixma mp160 of error msg. "ink absorber full" with a flashing of E 27? I read some ideas as to how to reset it above but for a different model. Does that matter or not? Hubby just home from hospital and I don't have time to take to a svc center. Many thanks!

    ReplyDelete

Service manuals and repair information about laser, dot matrix, label printer and ink jet printers of different makes: HP, Canon, Epson, Ricoh, Star, Xerox, Okidata