Saturday, August 22, 2009

Resetter canon 1980, 1880, iP2500, iP1900, iP1100, iP1800

Error printer Always appear message:
“The Ink Absorber is Full
Contact The service Center”.

Or Ink Full Tank usually indicator lamp on power and resume blinking many times

But don’t be afraid, You just follow this step :

Manual Reset Steps :

  1. Press and hold power button with your finger and then take in power cable
  2. Hold power button, then press resume button with your middle finger twice.
  3. Let in power button
  4. Printer doesnot blinking any more.
  5. At this step you had done Manual Reset Step and printer could be use again.
  6. But if manually your printer still error, you should use Reset Software permanently

Do this steps to get your printer permanently :

  1. Download software tool
  2. Extract file ZIP.
  3. Do GeneralTool.exe
  4. At USB Port choose your Port printer.
  5. Click Lock Release button
  6. Choose (check) EEPROM CLEAR
  7. Take blank paper to print. Then click Test Pattern 1 button
  8. Finish and your Printer will be normally

The methodes : here

Posted by at
Labels: , , , ,

16 comments:

  1. Error: The ink’s absorber is full.

    Procedure:

    1.) Plug the power cord and the USB cord.
    2.) ON your printer.
    3.) Press and hold the power button. (Do not release until step 7.)
    4.) Remove the power cord.
    5.) After 5 seconds, insert or return the power cord in its socket.
    6.) Press the reset / resume button for two times. (Reset / resume button located below the power button.)
    7.) Release the power button.
    8.) Press the reset/resume button for 4 times.
    9.) Run the IPTools software or the General Tools software for your printer model.

    IPTools Software – can be used only with Canon Pixma iP1200, iP1300, iP1880
    General Tools Software of Canon Pixma iP1880 will be used to reset the Canon Pixma iP198

    resetter Canon Pixma iP1200, iP1300, iP1500, iP1880, iP1980

    ReplyDelete

  2. Ok here is the procedure to reset the inm dupm counter but how can reset the ink????

    1. With the printer plugged in and powered off, press and hold the Resume/Cancel button, then press and hold the Power button. (DO NOT release the buttons. The LED light should be green to indicate that a function is selectable.).
    2. While holding the Power button, release the Resume/Cancel button. (DO NOT release the Power button.).
    3. While holding the Power button, press the Resume/Cancel button 2 times, and then release both the Power and Resume/Cancel buttons. (Each time the Resume/Cancel button is pressed, the LED lights alternately in orange and green, starting with orange.).
    4. When the LED light is green, press the Resume/Cancel button 4 times. (Each time the Resume/Cancel button is pressed, the LED lights alternately in orange and green, starting with orange.).
    5. Press the Power button. The LED lights in green, and the reset is performed. (When the operation completes, the printer returns to the menu selection mode automatically.).
    6. Press the power button to exit service mode.

    ReplyDelete

  3. Canon Ink Level Indicator Reset Procedures

    Ink Level Reset Instructions for Canon PG-40, PG-50, CL-41 and CL-51 cartridges

    With the cartridge facing the same way that it goes into the machine, but with the electronic strip facing you, do the following:

    1. Cover only the top row of contact pads that you see with tape.
    2. Put the cartridge in the printer, and it will give you a message "Cartridge Not Inserted".
    3. Remove the cartridge from the printer.
    4. Now cover only the top two rows of contact pads with tape.
    5. Put the cartridge in the printer, and it will again give you a message "Cartridge Not Inserted".
    6. Remove the cartridge from the printer again.
    7. Carefully, remove the tape that you had covering the top two rows of contact pads on the electronic strip.
    8. Place the cartridge back into the machine. The machine should now show that cartridge with a full status.

    This process is designed to work for one cartridge after each refill. It will need to be repeated for any other cartridges that you are refilling.

    ReplyDelete

  4. pls. help me with my canon ip1900, i wanted to clean the ink pads inside the printer but i could not open all the coverings, could anyone give steps, if possible with pic to open all the coverings so that i would have a better view and way to clean the spilled ink inside. it would be a great help. thanks...

    ReplyDelete

  5. thanks...it works magically... :)

    ReplyDelete

  6. Thank you very much! You did a great job for me...

    ReplyDelete

  7. is this method this work for ip1300 ?

    ReplyDelete

  8. It works on my Canon IP1900, great tuts and nice software. Best of all is FREE...

    THANKS

    ReplyDelete

  9. My Printer is IP1980 After I reset ink absorber is full message disappear. But now Power bulb is continually blinking. After reset the power. Please help me someone.

    ReplyDelete

  10. thank you very much.. that's solved my problem..

    ReplyDelete

  11. Thank you very much. It works for me.

    ReplyDelete

  12. Thank you so so so so so so much... i love it.... it work manually

    ReplyDelete

  13. my canon ip1980 series won't open up.

    ReplyDelete

  14. help my printer canon1900 stil blinking ...i follow the instruction above..and yet still bliking 2 green and 7times orange..

    please i really need printere

    ReplyDelete

  15. "the ink absorber is full"

    pls help me...Canon iP1980

    ReplyDelete

  16. "the ink absorber is full"
    pls help me...Canon iP1980

    -fmg

    ReplyDelete

Subscribe to: Post Comments (Atom)
Service manuals and repair information about laser, dot matrix, label printer and ink jet printers of different makes: HP, Canon, Epson, Ricoh, Star, Xerox, Okidata